Boat Plans Bruce Roberts | Guest cabin dressing room

Boat Plans Bruce Roberts

The basic layout of the cabin area below is as follows: Down four steps from the salon above. Once at the bottom of the steps, you can either turn left through a door and get to the master cabin, or go straight through another door to get to the guest cabin dressing room/hallway. One has to go through this area to get to the guest cabin/kids cabin located in the forward area of the hull. Each cabin has a door to access the common bathroom where the shower and toilet is located. Each cabin ( master and guest) has its own sink. The engine room is accessed from the master cabin through a water tight steel door.

Standing in the guest cabin dressing room, one will find a large sink base with storage underneath, four wall mounted cabinets, and a bench seat with storage underneath it. There will be two ceiling mounted DC lights, and one ceiling mounted AC light with all lights being controlled by switches on the wall. There is also a decent amount of wall space available to have some hanging storage without impacting ones ability to walk through the space.

Because of my wish filled thinking regarding shower sump pumps, I had to re think how I was going to hold the gray water from the shower and cabin sinks. I decided to add a holding tank, and the most logical place for it was under one of the bunks against the dressing room bulkhead. I was going to buy a plastic tank, but since I had enough stainless plate left over from the water tank construction I decided to fabricate my own and save some cash. The tank ended up with 47 gallons of capacity.


Under the sink base in the dressing room is some of the gray water plumbing. The through hull fitting you see is above the water line. When we have to hold our gray water, the blue valve will be shut and the black valve will be open. This will direct the water to the main sump which will then direct the water to the 47 gallon holding tank I just built. When we can discharge gray water, the blue valve will be open, the black valve will be closed, and the shower sump will discharge overboard via the black pipe when the sump selector valve is in that mode. Its a pretty simple set up albeit a bit on the bulky side, but I made everything from parts found in the shop and did not have to depart with any cash. The elbow on he end of the manifold is for the guest cabin dressing room sink once I get that sink installed.

I built four more cabinets to fill up the wall in this room, and stopped them well short of the port light. One of the cabinets will be the medicine cabinet above the sink, while the other three will be general storage. The cabinets are 12 inches deep at the base, and about 18" deep at the top. Im also using these cabinets as the chase for the air conditioning duct that will feed the guest/kids cabin. That duct will be a four inch flexible pipe.

In order to give one as much privacy as possible, there will be a door between the dressing room and the bunk room. The door will be 20" wide.

I had enough room to create a bench in the dressing room so people could sit down while they were getting dressed. I installed a piano hinge on the lid of the bench so the bench could double as a locker for more storage.

The room is a fuzz narrow, but Im able to easily navigate through it without bumping my knees or having to turn the least bit sideways. I think this space will be an important part of the boat in regard to helping all on board with privacy, and a sense of having ones own space. To be honest, this is a very comfortable room even though its function is mostly utilitarian.

I have six doors to build for this room, and one more sheet of plywood to install on the partition between the master cabin and this space. I also have to plug all the screw holes, sand everything, and get a coat or two of finish on the wood. Once those jobs are finished, Im ready to start work on the sleeping room and its four bunks. Once the doors are installed and some finish on the wood, Ill post some more pics.

Do you find information about Boat Plans Bruce Roberts are you looking for? If not, below may help you find more information about the Boat Plans Bruce Roberts. Thank you for visiting, have a great day.

Continue

Boat Plans Building | Anchor Winch

Boat Plans Building

Wood working continues in other parts of the boat, but I thought Id blog a bit about the anchor winch.

Id always intended on using a chain windlass to handle my anchor, but this used winch was available, so I made the switch to a deck winch. This type of winch is a pretty simple piece of equipment with very few working parts which should provide me with a reliable tool to handle the ground tackle. As you can tell, this is a used winch, but given the simple nature of the beast, it will not take much to go through it. Once Im done with the wood working, Ill do a re build on this winch.

The valving on this winch lets me power down, free spool, and power up. The line pull on the unit is 1500 lbs, which is adequate to handle my ground tackle.

I like the commercial, fish boat look of this winch, and I think it will look sharp on pulpit of my trawler. The winch is on the fence in terms of being just large enough for our boat. I spoke with the manufacturer, and they felt as if it would do the job. The line pull on the next two larger size models is the same, but the thickness of the metal base is more on the larger units, along with being able to handle more rode. This unit is cast aluminum, and the base plate ( the area where the winch bolts to my deck) thickness is 3/4". The manufacturer was concerned that a boat of my displacement might risk cracking the base plate if I were to get caught in a strong blow. He suggested that I use rope vs wire rope, and snub the anchor rode to a bit. The winch can handle 275 of 5/8" rope along with 40 of 3/8 chain leaving a 1" gap below the housing. I like to use a 5:1 scope when anchoring, and the amount of rode is at my minimum comfort level. Ive never anchored in more than 40 of water, but you never know.

Its nice to be able to check another item off the list.

Do you find information about Boat Plans Building are you looking for? If not, below may help you find more information about the Boat Plans Building. Thank you for visiting, have a great day.

Continue

Boat Plans And Kits | Handrails and winch battery box

Boat Plans And Kits

Winter is not wanting to let go of our small Ohio river town, so no work has been finished on the roof of our boat. As I sit here and type these words, a forecast for 7"-11" of snow, high winds, and close to zero degree temperatures is playing from my radio giving us the promise of an interesting day tomorrow. The mid range forecast  has temperatures staying in the teens and low 20s for the next ten days, so the snow were going to get tonight is going to stick around for a while. "In like a lion, out like a lamb" was how March was described to me while I was growing up.

So while continuing  painting rooms in the house, Ive managed to get some boat work done in the shop with material Ive had stockpiled. The handrail fabrication was the first job I wanted to get finished, and for the most part, went pretty smooth. The handrails are made of 3/4" schedule 20 stainless steel pipe. I want to paint the rails, and while cost could have been  lowered with mild steel, using stainless pipe will be better in the long run in regard to maintenance. Because of cost, pipe was used vs tube, and because of weight, thin walled pipe was used. Wall thickness on schedule 20 is about .095 so MIG welding and stick welding is easily used.

The handrail will be 36" tall, with the stanchions being 24" on center. The stanchions centers could have probably been stretched to 36", but 24 is what I laid out when I was framing the roof, and the doubler pads are already welded in place. Once I post about the handrail install, youll see what Im talking about regarding doubler pads. The stanchions were cut to length on the lathe using a parting blade, and a stop to  make sure they are all the same length. To make fit up idiot proof, I coped each stanchion to fit the rail. Some people call it notching, I call it coping, but what ever you call it, I accomplished this by using my mill and an annular cutter. An annular cutter , or a rotary broach, as some call it is nothing more than the baddest assed  hole saw youve ever seen. The 3/4" shaft of the cutter with flats milled in it, are really designed to be used in a mag drill with its specific chuck, but I was able to use a collett to hold the cutter in the mill. The pipe is beefy enough to be held in the mill vice, and the key to doing this coping is an extremely slow feed. Rigid holding of the part, a sharp tool, and a slow feed gave me top  notch results.

Because the rail is going to be painted, I was able to MIG weld it. The mast boom is being secured right now by hooking it to one of the cleats use to lift the wheel house last year. I  never got around to cutting off the cleats, and darn if theyve not come in handy for securing the kayaks, and in this case, also the boom. It made sense to me to weld a couple of stanchions to the hand rail over a mounting stanchion to be able to rest the boom and snatch it down with the cable.

Because were using electric winches to control the load and the boom, a battery box had to be built for the battery. To help keep things out of the weather, I hinged a lid to the box. The box has a partition in it to hold the battery on one side, and on the other side house the motor solenoids, the motor fuses, and a positive and negative buss bar. The motor fuses are 50 amp inline, and came without a cover of any sort. I really did not like having two hot posts unprotected, so I used an orifice shield for pipe to cover the posts of the fuses .

The battery Im using came out of my "slightly used, but still OK " inventory I keep in the back of the shop, and  is a group 31. This battery is not going to get heavy use, but I still had to decide how to keep it charged. The choices were charger in the wheel house with heavy wires. Heavy wires from the house bank with no battery on the roof. AC wires to the roof, with charger in the roof top box. Solar panel to charge the battery. I chose a solar battery charger.

The solar battery charger is 1.5 watt, and its my understanding that with this low wattage, I wont need a charge regulator. I dont know what type of panel this thing is, but in my shop with the panel just seeing shop lights, it puts out 12 volts. When I move the panel outside and its shady, it puts out 21 volts. When the panel sees sunlight, it puts out 23 volts. The panel came with a small diode light on it that blinked when it was charging, but that blinking caused the voltage to pulse erratically when no sun was shinning, so I took the panel apart and cut the wire lead to the diode light. With the light not blinking anymore, the voltage was steady. I might as well say now, that this panel cost $14.00 , and has nothing but great customer reviews. For the three days I had it connected to the group 31, it held the charge steady at 13.2 volts.

The whole electric winch thing might come back to bite me in the butt some day, so I should probably have a few manual blocks and tackles on board. But truth be told, for how low the winchs cost, I should probably have a spare winch on board. While the winchs are of low cost, they seem to be put together well, and appear to be  weather tight. Once theyre wired and operational, Ill probably cover them with something water tight, and keep things up to snuff.

In two weeks, the boat yard opens for season hours. In ten weeks, the harbor opens for business , and well be in the water. Theres no way Im going to have my off season boat "to do" list completed, but thats OK. D day for me to have the real list complete is late June, when the plan is to motor to Kentucky lake.

Cheers

     

Do you find information about Boat Plans And Kits are you looking for? If not, below may help you find more information about the Boat Plans And Kits. Thank you for visiting, have a great day.

Continue

Wooden Boat Plans Australia | A Drum style model sail winch

Wooden Boat Plans Australia

photos courtesy of "Larry Ludwig" at www.LudwigRCYachts.com, Ludwig Mfg.

==

From: "Stephen Pratt" :

"On the North Coast (Ohio), are using HiTec HS-725 or HS-785 Winches. Bob Luther developed a mechanism to work an endless loop system of sail control. Fits inside the Star 45 with plenty room to spare."

Do you find information about Wooden Boat Plans Australia are you looking for? If not, below may help you find more information about the Wooden Boat Plans Australia. Thank you for visiting, have a great day.

Continue